View Hyundai ThermoTechTL Inventory
(Click on the blue dots below to read more)
Inside Wall / Floor
- Aluminum roof bows and side posts.
- Versitex VR2 0.065″ liner on sides, front, doors, and ceiling
- Bulitex sub floor, 0.025″ thickness
- Aluminum duct floor, 1-1/4″ thick, 16,000 lb rating
- Water and debris resistant tail light housing.
- Stainless Steel rear frame.
|Length||Exterior: 53' 0" |
Interior: 52' 2"
|Width||Exterior: 102.36" |
Interior: 97.4" lining to lining
|Height||Exterior: 13' 6" |
|Capacity||65,000 GVWR |
3722 cu. ft. of interior volume
|Tare Weight||12,550 lbs|
|Side Sheets||Flat 0.040", pre-painted white aluminum side sheet.|
|Side Posts||Extruded aluminum "Z" side posts on 12" centers nose through support gear and 24" centers support gear to rear of trailer.|
|Roof||One-piece 0.032" thick aluminum, tension leveled prior to installation. Special corrugated roof sheet design allows roof to expand and contract without foam delamination or structural weakening of roof.|
|Roof Bows||Galvanized steel anti-snag bows on 24" centers. Pre-bonded to roof sheet. Roof bows installed using four solid rivets, two per end.|
|Front Wall||Stainless steel front impact plate and pre-painted 0.040" white aluminum sheets with 6.00" radius. Large opening refrigeration unit bracing.|
|Rear Frame||Stainless steel rear frame including corner posts, hinge butts, door header, and rear sill. Stop/tail/turn signals are fully recessed in the rear sill. Hot-dip galvanized hi-tensile steel bolt-on under-ride protection.|
|Rear Doors||Extruded aluminum frame type swing doors with dual durometer seals and 0.040" pre-painted white aluminum outer sheets. One easy-operating anti-rack lock rod per rear door. Lockrod handles are fitted with rubber grips for operator comfort and safety. Four heavy-duty extruded aluminum hinges per door are provided.|
|Lining||Sides: 0.065" Versitex VR2. |
Front: 0.065" Versitex VR2
Rear Doors: .065" Versitex VR2
Ceiling: 0.065" Versitex VR2
|Insulation||Injection foamed urethane insulation. Sides, floor and roofing 2" thick. Rear door 3" thick. Front wall 4" thick.|
|Refrigeration||Heavy duty mounting frame and bracing provided for large opening nose mounted unit.|
|Crossmembers||Five inch deep extruded aluminum I-beams on 12" centers from the end of the upper running gear rails to the support gear. Three inch deep hi-tensile aluminum I-beam cross members on 12" centers between the upper coupler and support gear. Four inch steel, 80,000# yield I-beams on 12" centers over the support gear and the upper running gear rails. Two additional I-beams are added in the last 4' of the trailer for additional impact resistance to severe loading conditions.|
|Upper Coupler Floor||Four inch deep with stainless steel front approach apron. A 1/4' thick approach plate and 1/4' thick top and bottom main beam plates. King pin is A.A.R. rated.|
Extruded aluminum 1-1/4" high duct type. Rear gutter is flush with top of floor. Last 4' of floor is reinforced for fork lift use with extruded aluminum inserts and a 43" deep × 96" wide composite bearing sheet. Two inch deep Apitong hardwood floor sills.
|Landing Gear||Two speed, 50,000 lb. capacity, A.A.R. rated with 10"×10" sand shoes. Roadside crank handle. Hot dipped galvanized mounting bracket and bracing.|
|Scuffband||Ten inch high extruded aluminum, recessed, foamed in place.|
|Underride Guard||Per CMVSS 223 Regulations High Tensel Steel. Bolt-on type with special 4" square tube, hot dipped galvanized with recess for conspicuity tape with end cap to prevent slippage|
|Suspension||Hedrickson Vantraxx HKANT40K Air Ride|
|Wheels||Steel hub piloted disc wheels 22.5"×8.25" with outboard mounted brake drums.|
|Tires||Low profile 22.5 radial tires.|
|Axles||Five inch round, 22,500 lb. rating, 77.5" track.|
|Brakes||Non-asbestos lining 16.5"×7" quick change type, "S" cam operated automatic slack adjuster.|
|Wheel Ends||Stemco Platinum Performance.|
|Lights & Wiring||Truck-Lite Model #33 side clearance lights, #33 LED rear header, #40 series stop/tail/turn lights and #60 series mid-turn signals. Sealed and internally grounded wiring harness with color-coded wiring, roadside mounted 7-way electrical connector, split pins and no circuit breaker.|
|PAINT & FINISH|
|Paint||All carbon steel parts abrasive blasted and coated with zinc rich epoxy primer. Exposed steel parts coated with a rust preventative topcoat. |
A second coat of enamel primer is applied and a gray enamel topcoat is applied to chassis and support gear. Pre-painted white steel disc wheels.
|Undercoating||Crossmembers pre-coated with black color coatings prior to installation. Landing gear and running gear areas painted with gray non-hardening rust preventative.|
|Decals||D.O.T. approved Hyundai Translead logo conspicuity tape and FHWA inspection sticker.|
|Miscellaneous||Truck-Lite P/N 97960 registration cardholder on frontwall. White mud flaps with Hyundai logo mounted on rear of slider subframe.|
|Warranty||Limited five year warranty.|
Hyundai Translead offers a wide variety of options and packages to fit your operations.
Please complete and submit the questionnaire below to the best of your knowledge and a Coast Hyundai Trailers sales representative will follow-up with you soon with additional information on your quote. (Blank items will default to OEM’s standard specification).